The Advantage of Tier-2 Testing for Fiber Optic Cabling

04/12/2017

The Advantage of Tier-2 Testing for Fiber Optic Cabling

When installing or maintaining a network, an OTDR (Optical Time Domain Reflectometer) is used to perform Tier-2 certification for fiber optic cabling.

The primary advantage of a Tier-2 test is that it provides information about each connection, splice and cable segment in the link and offers a graphical representation of the components and their performance.

An OTDR is unrivalled for troubleshooting because it creates a visual representation of the link allowing the operator to see the contribution of each component to the link’s total loss. Previously OTDRs were only used for troubleshooting in LANs because of their cost and complex operation. Today OTDRs are very easy to use and the costs have come down to a point where it is practical to use them for initial “turn-up” testing.

When certifying new cabling with an OTDR a snapshot is created, documenting the location and performance of every component at the time of installation. Should an issue arise later, a current OTDR test can be compared with the initial test to immediately identify what has changed in the cabling and the location of that fault.

An OTDR performs different measurements during a test. An OTDR classifies everything it “sees” as one of two categories of event - attenuation/non-reflective events or reflective events.

Attenuation events are those where power is lost going through the event and none is reflected back to the OTDR. Events that fall into this category are fusion splices, micro bends, macro bends and the fiber optic cable itself.

Reflective events are those where power is lost going through the event, and power is reflected back to the OTDR. Events that fall into this category are connections/bulkheads, mechanical splices, breaks in the fiber and the end of the fiber optic cable.

An OTDR will provide a number of very different looking traces when testing the same fiber depending on the OTDR’s wavelength, acquisition time and pulse width settings for each test. Ultimately, obtaining the perfect, single OTDR trace for a given cable is a matter of compromise that boils down to resolution (sharpness) versus dynamic range (max loss that can be measured). In some cases, there is no single setting that provides a perfect trace, so a cable may be tested with different settings providing two or more reports to capture every event.

Recent articles

  • Quick Setup Mode for LanTEK III® is Easy as 1,2,3 08/11/2018

    A new Quick Setup mode has been introduced to the LanTEK III Cable Certifier from IDEAL Networks, to help make your job as a cable installer easier and more efficient.  

    Read more
  • 4 IDEAL Networks Touchscreen Testers to Save You Time 01/10/2018

    We know that time is crucial for technicians testing and troubleshooting cable and network installations, so for faster and easier network troubleshooting, cable installation and transmission testing, we have introduced touchscreens to some of our popular IDEAL Networks testers.

    Read more
  • 5 ways SecuriTEST IP improves CCTV troubleshooting and installation 05/07/2018

    When faced with installing and maintaining CCTV security systems, you may find yourself having to switch between a whole range of different network testing equipment. With the new SecuriTEST IP CCTV camera tester for IP digital/HD coax and analogue systems from IDEAL Networks, this doesn’t have to be the case. Here are just a few of the ways that the SecuriTEST IP can help you improve productivity and overcome challenges using a single tester.

    Read more
  • VoIP troubleshooting – LanXPLORER PRO reviewed 05/04/2018

    When issues arise on VoIP systems it can disrupt conversations and impact voice quality.  Luckily, our test equipment can be used to measure key factors that impact network performance and VoIP quality, ensuring effective troubleshooting.

    Read more
  • How performance testing applies to security, alarm, and control systems, as well as voice and data systems 03/04/2018

    When it comes to performance testing, voice/data and security alarm or access control systems are becoming increasingly difficult to distinguish from each other. Data performance testers can now be used to test the data handling capabilities or cabling, no matter what the application. This is due to the current process of moving these systems over to Ethernet/IP.

    Read more